Images are examples, some edited with AI. The technical data are authoritative. AI notice
Digital output module CPX-AP-A-8DO-PI - Festo 8129107
- Specialist dealer since 2009
- Invoice payment for regular customers
- Worldwide shipping
- Technical questions clarified with the manufacturer
Technical data
| Dimensions (W x L x H) | 50.1 mm x 107.3 mm x 57.5 mm |
|---|---|
| Grid dimension | 50.1 mm |
| Type of mounting | Screw-clamped |
| Product weight | 98 g |
| Mounting position | Any |
| Ambient temperature | -20 ... 50 °C |
| Note on ambient temperature | Observe ambient temperature derating according to IEC 61131-2:2017 |
| Storage temperature | -20 ... 70 °C |
| Relative air humidity | 5 - 95%, Non-condensing |
| Nominal altitude of use | <= 2000 m ASL (> 79.5 kPa) |
| Max. installation height | 3500 m |
| Note on max. installation height | Observe ambient temperature derating according to IEC 61131-2:2017 |
| Corrosion resistance class CRC | 1 - Low corrosion stress |
| Vibration resistance | Transport application test with severity level 2 to FN 942017-4 and EN 60068-2-6 |
| Note on vibration resistance | Transport application test with severity class 1 to FN 942017-4 and EN 60068-2-6 |
| Shock resistance | Shock test with severity level 2 to FN 942017-5 and EN 60068-2-27 |
| Note on shock resistance | 30 g/11 ms to EN 60068-2-27, SG1 on DIN rail, SG2 on direct mounting, Shock test with severity level 1 to FN 942017-5 and EN 60068-2-27 |
| Protection class | III |
| Pollution degree | 2 |
| Overvoltage category | II |
| Max. cable length | 30 m outputs |
| LABS (PWIS) conformity | VDMA24364-B2-L |
| Fire test material | UL94 V-0 (housing) |
| Note on materials | RoHS compliant, Free of halogen, Free of phosphoric acid ester |
| Material cover | Reinforced PBT |
| Material screws | Nickel-plated steel |
| Material o-ring | Fluoro rubber |
| Diagnostics via LED | Diagnostics per channel, Diagnostics per module, Load power supply, Status per channel |
| Diagnostics per internal communication | Communication error, Short-circuit/overload in output signal, Electronics/sensors overvoltage, Load overvoltage, Electronics/sensors undervoltage, Load undervoltage |
| Max. address volume, outputs | 1 byte |
| Number of outputs | 8 |
| Module parameters | Configuration of voltage monitoring load supply PL, Behaviour after short circuit/overload at analogue output |
| Communication interface, protocol | AP |
| Note regarding operating voltage | SELV/PELV fixed power supplies required, Note the voltage drop |
| Note on nominal operating voltage DC | Protected Extra-Low-Voltage to IEC 60204-1 |
| Nominal operating voltage DC of load | 24 V |
| Permissible voltage fluctuation of load | ±25% |
| Nominal DC operating voltage, electronics/sensors | 24 V |
| Permissible voltage fluctuations for electronics/sensors | ±25% |
| Intrinsic current consumption at nominal operating voltage for electronics/sensors | Typically 40 mA |
| Intrinsic current consumption at nominal operating voltage load | Typically 5 mA |
| Power failure bridging | 10 ms |
| Potential separation between the supply voltages electronics/sensor technology and load/valves | Yes |
| Reverse polarity protection | Yes |
| Electrical connection output, function | Digital output |
| Electrical connection output, connection type | 8x terminal strip |
| Electrical connection output, connector system | Spring-loaded terminal |
| Electrical connection output, number of connections/cores | 4 |
| Electrical connection output, connection pattern | 00997388 |
| Electrical connection for output, conductor cross section | 0.25 ... 1.5 mm² |
| Electrical connection for output, note on conductor cross section | 0.13 - 1.5 mm² for flexible conductors without wire ferrule |
| Electrical connection for output, AWG conductor cross section | AWG24 - AWG16 |
| Characteristic for outputs | To IEC 61131-2, type 0.5 |
| Switching logic for outputs | PNP (positive switching) |
| Fuse protection of outputs (short circuit) | Internal electronic fuse per channel |
| Behaviour after end of overload of the outputs | No automatic return |
| Output delay with ohmic load | Signal change 0->1: < 200 µs, Signal change 1->0: < 200 µs |
| Max. residual current outputs per module | 4 A |
| Electrical isolation of outputs between channels | No |
| Electrical isolation of outputs between channel - internal communication | Yes |
| Max. power supply per channel | 0.5 A |
| Manufacturer | Festo |
| Hersteller-Nr | CPX-AP-A-8DO-PI |
| EAN | 4052568654474 |
| Zolltarifnummer | 85389099 |
| GPSR Herstellerdaten | Festo Vertrieb GmbH&Co. KG, Festo Campus 1, DE-73734 Esslingen, festo.com |
| Artikelzustand | New |
| Artikel-Authentizität | Original product |
Downloads
Questions about this item
Any other question?
Send us the item number and your question. We clarify technical details directly with the manufacturer and usually reply on the next working day.
