Images are examples, some edited with AI. The technical data are authoritative. AI notice

Servo motor 8629 W, 93.7 Nm standstill torque, holding brake, single-turn encoder EMMT-AS-190-L-HT-R3SB - Festo 8148393

Festo ✓ Original product Brand new

82.4 Nm nominal torque and 183.3 Nm peak torque make the EMMT-AS-190-L-HT-R3SB a drive for dynamic positioning tasks. Rated power 8629 W at 1000 1/min, designed for 680 V DC. A single-turn absolute encoder (EnDat 22) captures the rotor position, the holding brake holds 115 Nm.

Net
€5,064.38
excl. VAT
Item FES-8148393
Manufacturer no. EMMT-AS-190-L-HT-R3SB
Question about this item
  • Specialist dealer since 2009
  • Invoice payment for regular customers
  • Worldwide shipping
  • Technical questions clarified with the manufacturer

Description

82.4 Nm nominal torque at 1000 1/min: the Festo EMMT-AS-190-L-HT-R3SB servo motor delivers 8629 W rated power to the axis. Total moment of inertia is 195 kgcm².

Benefits

  • Peak torque 183.3 Nm for short cycles and acceleration phases
  • Speed up to 1654 1/min, nominal speed 1000 1/min
  • Single-turn absolute encoder with 19 bit resolution, EnDat 22 interface
  • Holding brake 115 Nm, operating voltage 24 V DC
  • Cogging torque below 1.0 % of peak torque, smooth running even at low speeds
  • Degree of protection IP21, ambient temperature -15 to 40 °C

Application

Typical uses are positioning axes, feed systems and pick-and-place units. Before mounting, match the interface and shaft loads of the EMMT-AS-190-L-HT-R3SB to the mechanics.

Technical data

TypeEMMT-AS-190-L-HT-R3SB
Festo part no.8148393
Ambient temperature-15 to 40 °C
Note on ambient temperatureUp to 80°C with derating of -1.5% per degree Celsius
Maximum installation height4000 m
Note on maximum installation heightAs of 1,000 m: only with derating of -1.0% per 100 m
Storage temperature-20 to 70 °C
Relative air humidity0 - 90%
Conforms to standardIEC 60034
Temperature class as per EN 60034-1F
Maximum winding temperature155 °C
Rating class as per EN 60034-1S1
Temperature monitoringDigital motor temperature transmission via EnDat® 2.2
Motor type to EN 60034-7IM V1, IM V3
Mounting positionAny
Degree of protectionIP21
Note on degree of protectionIP67 for motor housing including connection components
Concentricity, coaxiality, axial runout to DIN SPEC 42955N
Balance qualityG 2.5
Detent torque&lt,1.0% of peak torque
Bearing lifetime under nominal conditions20000 h
Interface code, motor out190B
Electrical connection 1, connection typeHybrid plug
Electrical connection 1, connector systemM40x1
Electrical connection 1, number of connections/cores15
Electrical connection 1, connection pattern00997380
Pollution degree2
Note on materialsRoHS compliant
Corrosion resistance class CRC0 - No corrosion stress
LABS (PWIS) conformityVDMA24364 zone III
Vibration resistanceAs per EN 60068-2-6
Shock resistanceAs per EN 60068-2-29, 15 g/11 ms to EN 60068-2-27
ApprovalRCM, c UL us - Recognized (OL)
CE mark (see declaration of conformity)To EU EMC Directive, To EU Low Voltage Directive, In accordance with EU RoHS Directive
UKCA marking (see declaration of conformity)To UK RoHS instructions, To UK regulations for electrical equipment
Certificate issuing authorityUL E342973
Nominal operating voltage DC680 V
Type of winding switchStar inside
Number of pole pairs5
Standstill torque93.7 Nm
Nominal torque82.4 Nm
Peak torque183.3 Nm
Nominal rotary speed1000 1/min
Maximum rotational speed1654 1/min
Maximum mechanical speed8000 1/min
Angular acceleration100000 rad/s²
Nominal power rating of motor8629 W
Continuous stall current22.8 A
Nominal motor current20 A
Peak current49.7 A
Motor constant4.12 Nm/A
Standstill torque constant4.79 Nm/A
Voltage constant, phase-to-phase289.7 mVmin
Phase-phase winding resistance0.358 Ohm
Phase-phase winding inductance13.8 mH
Winding longitudinal inductivity Ld (phase)6.95 mH
Winding cross inductivity Lq (phase)6.9 mH
Electric time constant38.8 ms
Thermal time constant80 min
Thermal resistance0.3 K/W
Measuring flange450 x 450 x 30 mm, steel
Total mass moment of inertia of output195 kgcm²
Product weight61500 g
Permissible axial shaft load520 N
Permissible radial shaft load2620 N
Rotor position sensorAbsolute encoder, single turn
Rotor position sensor, manufacturer designationECI 1319
Rotor position sensor, absolute detectable revolutions1
Rotor position encoder interfaceEnDat 22
Rotor position sensor, encoder measuring principleInductive
Rotor position sensor, DC operating voltage5 V
Rotor position sensor, DC operating voltage range3.6 to 14 V
Rotor position sensor, position values per revolution524288
Rotor position transducer resolution19 bit
Rotor position sensor, system accuracy of angle measurement-65 to 65 arcsec
Brake holding torque115 Nm
Operating voltage DC for brake24 V
Brake current consumption2.08 A
Power consumption, brake50 W
Brake separation time190 ms
Brake closing time65 ms
DC brake response delay12 ms
Maximum brake no-load speed8000 1/min
Maximum friction per braking process62000 J
Number of emergency stops per hour1
Total brake friction13000 kJ
Mass moment of inertia of brake50 kgcm²
Switching cycles holding brake5 million idle actuations (without friction work)
Mean time to failure (MTTF), subcomponent190 years, rotor position encoder
Energy efficiencyENEFF (CN) / Class 1
ManufacturerFesto
Hersteller-NrEMMT-AS-190-L-HT-R3SB
EAN4052568592332
Zolltarifnummer85015230
GPSR HerstellerdatenFesto Vertrieb GmbH&Co. KG, Festo Campus 1, DE-73734 Esslingen, festo.com
ArtikelzustandNew
Artikel-AuthentizitätOriginal product
AusführungSingleturn-Absolutwertgeber, mit Haltebremse
NormDIN EN 60034-1, DIN EN 60034-7, DIN EN 60034
SeriesEMMT
Protection ratingIP21
Temperature (max.)40

Downloads

Questions about this item

Any other question?

Send us the item number and your question. We clarify technical details directly with the manufacturer and usually reply on the next working day.

Customers Who Bought This Item Also Bought